Sv translation | ||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ||||||||||||||||||||||
Das Übersetzungsverhältnis der verwendeten Stromwandler ist erforderlich für die korrekte Bestimmung der Messwerte. Einstellungen:
Messmodus (bei Dreileiter unbedingt erforderlich)
SpannungsreferenzFalls Sie den Stromkanal vertauscht haben (z.B. L1 und L3 vertauscht), können Sie dies hier korrigieren. Tausche s1(k) und s2(l)Falls Sie den Stromwandler dieses Kanals falsch angeschlossen haben, können Sie dies hier korrigieren. Beispiel-Bild: UMG 96-PQ-L Messgruppenmodus für L1..L4 *
Beispiel-Bild: UMG 96-PQ-L-LP Stromkanal L1-L3Die Stromwandler für die Kanäle L1 bis L3 müssen das gleiche Wandlerverhältnis besitzen.
Beispiel-Bild: UMG 96-PQ-L Stromkanal L4 *
Multifunktionskanal L5 *Wenn für den Kanal (Klemmen 29+30) der Messmodus = DC-Leistung ausgewählt ist, geben Sie hier das Stromwandlerverhältnis ein.
|
Sv translation | ||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ||||||||||||||||||||||
The ratio of the current transformers used is required to be able to determine the measured values correctly. Settings
Measuring mode (absolutely essential for three-wire systems)
Voltage referenceIf you have swapped the current channel (e.g. L1 and L3 swapped), you can correct this here. Swap s1(k) and s2(l)If you have connected the current transformer of this channel incorrectly, you can correct this here. Example image: UMG 96-PQ-L Measurement group mode for L1..L4 *
Example image: UMG 96-PQ-L-LP Current channel L1-L3The current transformers for channels L1 to L3 must have the same transformer ratio.
Example image: UMG 96-PQ-L Current channel L4 *
Multifunction channel L5 *If Measuring mode = DC power is selected for the channel (terminals 29+30), enter the current transformer ratio here.
|
Sv translation | ||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ||||||||||||||||||||||
La relación de transformación de los transformadores de corriente utilizados es necesaria para determinar correctamente los valores de medición. Ajustes:
Modo de medición (imprescindiblemente requerido para 3 conductores).
Voltage Reference (Referencia de tensión)Si ha intercambiado el canal de corriente (p. ej, L1 y L3), podrá corregirlo aquí. Change s1(k) and s2(l) (Cambiar s1(k) y s2(l))Si ha conectado incorrectamente el transformador de corriente de este canal, podrá corregirlo aquí. Imagen de ejemplo: UMG 96-PQ-L Measurement Group Mode for (Modo del grupo de medición para) L1..L4 *
Imagen de ejemplo: UMG 96-PQ-L-LP Current Channel (Canal de corriente) L1-L3Los transformadores de corriente para los canales L1 hasta L3 tienen que tener la misma relación de transformador.
Imagen de ejemplo: UMG 96-PQ-L Current Channel (Canal de corriente) L4 *
Canal multifunción L5 *Si para el canal (bornes 29+30) está seleccionado el modo de medición = potencia CC, introduzca aquí la relación del transformador de corriente.
|
Sv translation | ||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ||||||||||||||||||||||
Il rapporto di trasformazione dei trasformatori di corrente utilizzati è necessario per la corretta determinazione delle letture. Impostazioni:
Modalità di misurazione (assolutamente necessaria per i tre conduttori)
Riferimento di tensioneSe il canale della corrente è stato scambiato (ad esempio L1 e L3), è possibile correggerlo qui. Scambio s1(k) e s2(l)Se il trasformatore di corrente di questo canale è stato collegato in modo errato, è possibile correggerlo qui. Immagine di esempio: UMG 96-PQ-L Modalità gruppi di misura per L1..L4 *
Immagine di esempio: UMG 96-PQ-L-LP Canale corrente L1-L3I trasformatori di corrente per i canali da L1 a L3 devono avere lo stesso rapporto di trasformazione.
Immagine di esempio: UMG 96-PQ-L Canale di corrente L4 *
Canale multifunzione L5 *Se per il canale (morsetti 29+30) è selezionata la modalità di misurazione = Potenza DC, inserire qui il rapporto del trasformatore di corrente.
|